Mobile modems and routers

Modems which use mobile phone lines (GPRS, UMTS, HSPA, EVDO, WiMax, etc.), are known as cellular modems. Cellular modems can be embedded inside a laptop or appliance, or they can be external to it. External cellular modems are datacards and cellular routers. The datacard is a PC card or ExpressCard which slides into a PCMCIA/PC card/ExpressCard slot on a computer. The best known brand of cellular modem datacards is the AirCard made by Sierra Wireless.[citation needed] (Many people just refer to all makes and models as AirCards, when in fact this is a trademarked brand name.)[citation needed] Nowadays, there are USB cellular modems as well that use a USB port on the laptop instead of a PC card or ExpressCard slot. A cellular router may or may not have an external datacard (AirCard) that slides into it. Most cellular routers do allow such datacards or USB modems, except for the WAAV, Inc. CM3 mobile broadband cellular router. Cellular Routers may not be modems per se, but they contain modems or allow modems to be slid into them. The difference between a cellular router and a cellular modem is that a cellular router normally allows multiple people to connect to it (since it can route, or support multipoint to multipoint connections), while the modem is made for one connection.

Most of the GSM cellular modems come with an integrated SIM cardholder (i.e., Huawei E220, Sierra 881, etc.) The CDMA (EVDO) versions do not use SIM cards, but use Electronic Serial Number (ESN) instead.

The cost of using a cellular modem varies from country to country. Some carriers implement flat rate plans for unlimited data transfers. Some have caps (or maximum limits) on the amount of data that can be transferred per month. Other countries have plans that charge a fixed rate per data transferred—per megabyte or even kilobyte of data downloaded; this tends to add up quickly in today's content-filled world, which is why many people are pushing for flat data rates.

The faster data rates of the newest cellular modem technologies (UMTS, HSPA, EVDO, WiMax) are also considered to be broadband cellular modems and compete with other broadband modems below.

RS-232

In telecommunications, RS-232 (Recommended Standard 232) is a standard for serial binary data signals connecting between a DTE (Data Terminal Equipment) and a DCE (Data Circuit-terminating Equipment). It is commonly used in computer serial ports. A similar ITU-T standard is V.24.



The standard does not define a maximum cable length but instead defines the maximum capacitance that a compliant drive circuit must tolerate. A widely-used rule-of-thumb indicates that cables more than 50 feet (15 metres) long will have too much capacitance, unless special cables are used. By using low-capacitance cables, full speed communication can be maintained over larger distances up to about 1,000 feet. For longer distances, other signal standards are better suited to maintain high speed.

Since the standard definitions are not always correctly applied, it is often necessary to consult documentation, test connections with a breakout box, or use trial and error to find a cable that works when interconnecting two devices. Connecting a fully-standard-compliant DCE device and DTE device would use a cable that connects identical pin numbers in each connector (a so-called "straight cable"). "Gender changers" are available to solve gender mismatches between cables and connectors. Connecting devices with different types of connectors requires a cable that connects the corresponding pins according to the table above. Cables with 9 pins on one end and 25 on the other are common. Manufacturers of equipment with 8P8C connectors usually provide a cable with either a DB-25 or DE-9 connector (or sometimes interchangeable connectors so they can work with multiple devices). Poor-quality cables can cause false signals by crosstalk between data and control lines (such as Ring Indicator).

DDR3 SDRAM

In electronic engineering, DDR3 SDRAM or double-data-rate three synchronous dynamic random access memory is a random access memory interface technology used for high bandwidth storage of the working data of a computer or other digital electronic devices. DDR3 is part of the SDRAM family of technologies and is one of the many DRAM (dynamic random access memory) implementations.

DDR3 SDRAM is an improvement over its predecessor, DDR2 SDRAM, and the two are not compatible. The primary benefit of DDR3 is the ability to transfer at twice the data rate of DDR2 (I/O at 8× the data rate of the memory cells it contains), thus enabling higher bus rates and higher peak rates than earlier memory technologies. There is no corresponding reduction in latency, as that is a feature of the DRAM array and not the interface.[citation needed] In addition, the DDR3 standard allows for chip capacities of 512 megabits to 8 gigabits, effectively enabling a maximum memory module size of 16 gigabytes.

With data being transferred 64 bits at a time per memory module, DDR3 SDRAM gives a transfer rate of (memory clock rate) × 4 (for bus clock multiplier) × 2 (for data rate) × 64 (number of bits transferred) / 8 (number of bits/byte). Thus with a memory clock frequency of 100 MHz, DDR3 SDRAM gives a maximum transfer rate of 6400 MB/s.

It should be emphasized that DDR3 is a DRAM interface specification; the actual DRAM arrays that store the data are the same as in any other type of DRAM, and have similar performance.